| Si
No |
Price | |
 1 |
LPG
Detector/Alarm This alarm is highly useful for detecting presence of any traces Liquefied Petroleum Gas. It may be used in the kitchen, Hotels, LPG operated vehicles and too in LPG tankers. The kit detects the LPG vapours in the air and sounds an alarm along with Relay which can be used to switch any bigger loads |
880/- |
| 2 |
Infrared
Obstacle detector. This kitt can be put to variety of uses where obstacle detection is required. The circuit emits modulated infrared beam through IR led and receives the reflected light back and trigger a “low” logic when ever an obstacle is detected. The range of detection can be varied up to 4-6 inches for white surface with on-board variable resistor (This is a complelte assembled and tested kit. No decription or schematics will be given with this kit). |
200/- |
| 3 |
Microcontroller
based automatic flush system Here is an automatic flush system (toilet and urinal) that automatically flushes the fixture when the user departs. It employs an AT89C2051 microcontroller and an infrared sensor to detect a user approaching the fixture, then waits until the user departs. It also flushes before the person departs if the person is present for more than the preset time (5 minutes). CD4050 is used as a buffer for the output ports of the microcontroller, TSOP1738 is used as an IR sensor and a solenoid is used to actuate the flush from a 6V power supply with a battery backup inside the unit. |
725/- |
| 4 |
AT89C2051
Based Count down timer Here is a microcontroller based timer that performs countdown operation for up to 99 minutes with two 7-segment displays showing the actual time left. During the countdown operation, a relay is latched and a flashing LED indicates countdown timing's progress. The program in the 20-pin Atmel AT89C2051 microcontroller used in the circuit can be easily modified to suit users' requirements. A relay driver section is included in the circuit to switch on a relay that can activate any electrical device. Apart from microcontroller, CD4511 and LTS543 are some of the main components used in the circuit. |
715/- |
|
5 |
Microcontroller
Based Bi-Directional Visitor Counter. Here is a low-cost AT89C52 microcontroller-based visitor counter that can be used to count the number of persons at a place. It consists of three 7-segment displays (LTS 543) to display the number of visitor's up to 999. The circuit works off a 5V DC supply. Some of the main components include IR LED's, L14F1 photo transistors, LM324 quad op-amp and 7805 regulator. |
1100/- |
| 6 |
Burglar
Alarm This circuit sounds a loud alarm in the case of an unauthorized entry. Wire loop gets broken whenever such an attempt is made. Number of ICs used: None |
107/- |
| 7 |
Cell
Tracker (Mobile detector bug) This gadget detects the transmission of any cellular phone operating in the ultra high frequency range in 1.5 meters of its radius. This battery operated gadget is highly helpful in classrooms and examination centers to prevent malpractices. Number of ICs used: 5 |
306/- |
| 8 |
Cordless
FM MIC The voice at condenser microphone can be listened through a standard FM receiver using this circuit. The range of this FM transmitter can be easily enhanced with little modifications. Number of ICs used: None. |
186/- |
| 9 |
89C51 based Digital water level controller with LCD This circuit based on 89C51 Atmel Microcontroller, controls the pump used to fill the water in Overhead tank. The kit protects motor against Low voltage, High Voltage, and too dry run of the pump in absence of water. All events like Standby, Motor On, Low voltage, High Voltage, and Dry run are displayed on a 16 x 2 LCD display. |
1850/- |
| 10 |
Electronic
Auto Dipper At night, the high beamed head light lamp of vehicle approaching from opposite direction causes the problem for drivers. This circuit solves the problem by making the dipper action automatic. As soon as it senses the light rays coming from opposite direction it automatically turns lamps from High to Low intensity. Number of ICs used: None. |
208
/- |
| 11 |
Electronic
Guard for Blind Using this Infrared based aid for visually impaired persons, any obstruction in the path can be sensed easily. When obstruction is too near, the loudness level of sound coming through earphone gets increased. Thus the user holding the unit gets a rough idea of his distance from the object. The important feature of the circuit is its small size owing to use of less number of components. After little modifications, the same circuit can be used in robotic toys or in object counters. Number of ICs used: 1 |
349/- |
| 12 |
Fastest
Finger First Indicator ….... Useful in quiz and game shows, this device indicates the fastest player's designation / selection number along with alarm sound, locking other contestant buttons. This can be reset with a reset button provided. Number of ICs used: 7. |
377/- |
| 13 |
Fire Alarm This fire alarm uses a germanium diode as sensor to sense fire and activate a loud alarm. Number of ICs used: 1. |
118/- |
| 14 |
Infrared Object Counter This circuit can be installed in public places to count the number of people or objects passing through the transmitter & receiver. The circuit operates at a frequency of 38 KHz. The count will be displayed through the calculators. Number of IC used: - 3 |
321/- |
| 15 |
IR Remote Switch Switch ON/OFF of any appliance can be done using this remote receiver. The circuit uses any TV, VCR, VCD or CD player remote as transmitter. Indication of different output stages is provided by LED's. The approximate range of the circuit is about 10 meters. Number of ICs used: 3 |
208/- |
| 16 |
Knock Alarm This circuit converts knock on door, car's dashboard, drawer, etc into a loud alarm using a loudspeaker. It can also be used to warn you of any unauthorized entry during night time, if installed at your doorstep. Number of ICs used: 1. |
152/- |
| 17 |
Long Range Burglar Alarm using laser torch |
355/- |
| 18 |
Long-Range
FM Transmitter The high-power output obtained using a power amplifier stage allows a range of about 2 km for this FM transmitter. Reasonable good signal quality and strength are possible with little adjustments. Number of ICs used: None. |
265/- |
| 17 |
Low Cost Energy Meter based on ADE 7757 As the name suggests "Low cost energy meter" has been constructed with the help of IC ADE 7757. The output units are displayed in the seven segment display. These can measures up to (9,99,999.The circuit is also provided with the proper battery back-up such that even if the power fails the display will not be reset & it goes on. IC used 2. |
1175/- |
| 18 |
Manual
EPROM Programmer This circuit can manually programs EPROM (2716, 2732) with the help of 8 way dip switches. Two 8 way dip switches are provided one for the address of the program and the other for the date of the program. This circuit is quite inexpensive and very useful to program your EPROM by yourself. Number of IC used: - 2 Nos |
658/- |
| 19 |
Low
Cost Energy Meter based on ADE 7757 As the name suggests "Low cost energy meter" has been constructed with the help of IC ADE 7757. The output units are displayed in the seven segment display. These can measures up to (9,99,999.The circuit is also provided with the proper battery back-up such that even if the power fails the display will not be reset & it goes on. IC used 2. |
1175/- |
| 19 |
AT89C52
Microcontroller Based Industrial Timer Here is a simple industrial timer based on 40-pin Atmel AT89S52 microcontroller that performs count-down operation up to 9999 minutes/second with four 7-segment displays showing the actual time left. The relay energizes as you press the start switch and remains on till the countdown reaches0000.Four push-to-on switches are used to start/stop, select either minutes or seconds, and set the initial value for countdown operation (using up and down keys). |
1690/- |
| 20 |
Digital Voltmeter Digital Voltmeter is designed as a panel meter which can be used in DC power supplies, or where it is necessary to have anaccurate indication of the voltage. |
575/- |
| 21 |
MOSFET
Based Pre-Amplifier for FM Radio DXing Frequency Modulated (FM) transmission can be received within a range of about 40 Kms. To receive your favourite FM radio station beyond this range, the only option left is to connect an external pre-amplifier at the receiver end. This circuit acts as FM booster attached to your present FM radio receiver and enables one to receive FM in fringe areas. Number of ICs used: None |
287/- |
| 22 |
Musical
Hold On for Telephone Using this add-on external circuit attached to your telephone a melodious music is generated on telephone line. During the entire hold-on interval, person on other end enjoys a pleasant music. To resume talking when you are back, just flick the switch to OFF position. A Red LED included in the circuit indicates that phone line is on-hold and it automatically turns OFF when music stops. Number of ICs used: 1. |
118/- |
| 23 |
Parallel
Telephone Ringer Due to high volume of your hi-fi audio/video systems or any other reason sometimes telephone ringing in other room is not heard. In addition to provide indication that your telephone is ringing in other room this telephone extension ringer avoids overhearing of conversation by an undesired person at other end. Number of ICs used: 1. |
152/- |
| 24 |
89C51
Programmer with Monitoring System This kit contains all the necessary items to build a programmer for AT89C51 micro-controller along with one sample project. The programmer directly interfaces with PC parallel port. Included CD contains assembler, programmer software and 89C51 details. The sample project of monitoring system can be used for promptly calling room service or assisting staff in establishment like hotels, small offices, clinics etc. It provides audio-visual identification of calling point. This kit thus acts as an easy interactive tool to start working on microcontrollers. Number of ICs used: 6 |
1685/- |
| 25 |
PC
based Oscilloscope for Serial port This kit conditions different signals of frequency below 1 KHz and displays their waveforms on the PC's screen. The hardware converts input waveform to digital format for interfacing to the PC. The software written in 'C' language acquires data into PC and displays it on screen. The program provides facility to alter the display and timing settings so that input waveform is correctly reproduced. Number of ICs used: 8 |
658/- |
| 26 |
PC Based Timer This circuit interfaced with PC computer through D-25 pin male connector, can switch on and switch off the device for a particular timing required by the user. The program is written in C languages & compiled in Turbo C compiler. The maximum timing of the circuit is for 18 hours. Number of ICs used: - 1. |
231/- |
| 27 |
Microcontroller-Based
Code Lock This simple code lock project is based on a 20-pin ATMEL microcontroller AT89C2051.It employs a 4-digit sequential code with time-out security feature. Apart from the microcontroller, the main components include CD4050 non-inverting buffer, LCD display and 7805 regulator. |
980/- |
| 28 |
FM
Booster Here is a low-cost circuit of an FM booster that can be fed between your FM receiver and the antenna to listen to distant commercial FM stations clearly. The main components of the circuit comprises of CS2570 transistor, trimmers and inductor coils. |
105/- |
| 29 |
Quality FM Transmitter The digital like sound quality that FM offers is the reason that many people prefer to have their own transmitting station in FM band. This quality FM transmitter can transmit chosen music in FM band. To receive its signals, any conventional FM radio receivers can be used. Without complicating the functionality, this circuit transmits the signals just by using discrete components. It provides an easy way to transmit less distorted, low noise music with in a range of about 200 meters. Number of ICs used: None. |
242/- |
| 30 |
Remote
Controled Digital Audio Processor This infrared (I R) remote controlled digital audio processor has four stereo input channels and one stereo output. The processors in this system control various functions of each channel and output them to your audio amplifier. |
1860/- |
| 31 |
Remote Control for Home Appliances This handy circuit can be used to switch on and off any of your home appliances or any electrical device with a single press of your TV, VCD or DVD remote control. This low-cost circuit is based on 4017 counter IC which receives trigger pulse from I R sensor and switches on the relay through which electrical devices are switched on & on receiving the 2nd pulse the device is switched off. |
265/- |
| 32 |
Remote controlled Land Rover The project integrates a number of different circuits, (with proper explanation of their underlying principles) to achieve the working model of a Land rover vehicle, which can be remotely instructed to perform the following functions though momentary depression of appropriate push switch on remote. Move in forward direction with front LED's lit. Move in reverse direction with back LED's lit. Turned to left with blinking left LED indication. Turned to right with blinking right LED indication. Stopped at any time, with all LED's extinguished. Provision is also made for its automatic stop on encountering a physical obstruction while moving in forward and reverse directions. Geared motors and detailed plans for fabrication is also included |
3425/- |
| 33 |
Speed
Checker for Highways With the two lasers installed at 100m apart on one side and corresponding LDRs on the other side of the highway, when the vehicle crosses the two laser beams, this circuit can check the speed of a vehicle through the readings on a 7-segment display unit. It also activates an audio alarm (piezo-buzzer) when the vehicle exceeds the permissible limit. |
658/- |
| 34 |
Stepper motor control using micro-controller This circuit is based on 89C51 microcontroller. It provides to control the rotation of a DC stepper motor in clockwise as well as anticlockwise direction. This module is simple and easy to construct and can be used in many application e.g. Machine control, Robotics. |
1410/- |
| 35 |
Teleremote- Control This remote overcomes the range barrier of infrared remotes. Control is provided through the dial keypad of a remote telephone and switching on/off operation of up to ten appliances is possible. (This circuit is meant to control only four devices.) Number of ICs used: 8 |
602/- |
| 36 |
Temperature
indicator using 89C52 It is microcontroller based temperature indicator which displays the temperature in the range of -55 degree Celsius to 125 degree Celsius. The Indictor output the calibrated date in digital form. It uses a temperature sensor Chip. Total No. of IC used - 3. |
1466/- |
| 37 |
Variable Power Supply with Digital Control A regulated power supply is one of the most important and essential requirements in electronic lab. The available power supply must provide variable outputs in steps. This kit gives variable and fluctuation-free DC voltage as output in the range of 1.5V to 12V. It also provides proper display using LED's as indicators and outputs here are easy to select. ICs used: 4 |
321/- |
| 38 |
Voice Recording and playback This circuit enables to record a single message of upto 60 seconds duration or upto eight different messages of 7.5 sec duration each. In playback mode the circuit plays recorded message either randomly or in sequential manner. It uses Voice Processor IC as main unit. Number of ICs used: - 2. |
602/- |
| 39 |
Water Level Controller This circuit provides switching control of pump motor and pumps water from ground-level tank to overhead tank when the tank is completely empty. To monitor the status, each tank is provided with three probes. Number of ICs used: 2. |
295/- |
| 40 |
Water level Controller-cum-Motor Protector This device provides switching on/off of motor, automatic switching off of motor when overhead tank is full and low- and high-voltage cut-off. Number of ICs used: 1. |
242/- |
| 41 |
Remotely
Programmable RTC - Interfaced Microcontroller for Multiple devices
Control with RC5 remote kit This project is based on AT89C52 Microcontroller and DS12887 Real-Time-Clock. It also includes an 82C55 Programmable Peripheral Interface chip to program the switching operation of 24 electrical appliances. A 16x2 LCD module is used as a user interface to display the time setting such as month, date, hour, minute, device number and on/off status of the device. Philips TV remote control is used to program the microcontroller and control the devices. Other main components used in the project include 74LS138, 74LS573, ULN2803 and TSOP1738. |
2548/-
|
| 42 |
Two-Channel
PC Based USB Oscilloscope Presented here is an oscilloscope using USB port of the PC that operates at up to 10 kHz with ±16V input voltage. The oscilloscope uses IC PIC18F2550 microcontroller chip from Microchip as the main controller, which makes the oscilloscope compact as there is no need of additional power supply for the entire circuit board. This controller chip along with MCP6S91, LF353 and L7660 ICs are used in the project. The project can be run in a PC with Windows 98SE operating system. |
1550/- |
| 43 |
Microcontroller-based Ultrasonic distance meter This project employs 40 kHz ultrasonic transducers for distance measurement up to 2.5 meters according to the author and 75 centimeters in practical. Ultrasonic transducers measure the amount of time taken for a pulse of sound to travel to a particular surface and return as the reflected echo. This circuit calculates the distance based on the speed of sound at 25°C ambient temperature and shows it on a 7-segment display. Some of the main components used in this project are : AT89C2051 microcontroller, two 40kHz ultrasonic transducers (one each for transmitter and receiver), current buffer ULN2003, operational amplifier M324, inverter CD4049, four 7-segment displays, five transistors and some discreet components. |
1430/- |
| 44 |
Cell
phone operated land Rover In this project, the robot is controlled by a mobile phone that makes a call to the mobile phone attached to the robot. In the course of a call, a tone corresponding to the button pressed is heard at the other end of the call. The robot perceives this tone with the help of the phone stacked in the robot. The received tone is processed by the microcontroller with the help of a MT8870 decoder. The microcontroller is preprogrammed to take a decision for any given input and outputs its decision to motor drivers in order to drive the motors for forward or backward motion or a turn. Some of the main components used are : MT8870 DTMF decoder, ATmega16 AVR microcontroller, L293D motor driver and 74LS04 NOT gate.(Cell phone is not provided along with the kit) |
2975/- |
| 45 |
Microcontroller
based tacho meter This is an easy-to-make photoelectric based tachometer project for measuring the RPM (revolution per minute) of rotating shaft, shop-floor tools and many household machines without any mechanical or electrical interface. The circuit employs AT89C2051 microcontroller as the main controller. Some of the major components used in the circuit are CA3140 operational amplifier, ULN2003 current buffer and KLQ564 4-digit,7-segment display. |
660/- |
| 46 |
Microcontroller
based Heart rate Meter This project demonstarates the Heart rate meter with which the heart beats per minute can be read. The project uses a light source and a photo detector to measure the variations in blood flowing across a finger and the variations are calculated and the result displayed on a 7 segment display. |
830/- |
| Projects
mentioned below are available on CD with complete project descriptions, Datasheets, Schematics, PCB component side layouts and sample source codes. |
||
| 1 |
Remote
controlled switch board with fan regulator with AT89S52 This remote controlled switch board switches 4lights and one fan with regulator using infrared based remote controller provided with the kit. The status of the six lights will be displayed by LED’s on the PCB whereas the speed of the fan will be digitally displayed by seven segment display connected to the AT89S52 microcontroller which controls all the vital functions of the switch board. |
5600/- |
| 2 |
4 channel
Remote for robotics with "Holtek" En/decoders This is a remote controller which is widely used in robotic application where in momentary mode, 4 channels can be used and in case latched outputs are required, 3 channels are available. Receiver side is equipped with four relays at the out put which can be wired in any configuration for the required operation. Individual addresses can be selected to operate more than one remote kit at a time. |
1850/- |
| 3 |
89C52 based school bell system using Dallas 1307 RTC This innovative bell system designed using Dallas DS1370 real time chip which is further used in conjunction with Atmel 89C52 for setting various bell timings of a day. Long bell and short bell rings can be individually selected using user friendly menu's displayed on a 16 × 2 LCD. The bell may be an AC 220 volt operated device which is switched through a BT12/600 Triac and MOC3021 Optocoupler. |
5800/-
|
| 4 |
Microcontroller based Hotel bell / Nurse calling bell system As compared to the regular multiple wired calling bell system, here we present an ultramodern Digital calling bell system, comprising of 2 units namely the Master module and the Slave. Each slave module represents a particular room or caller and the codes sent by the slave, are read by the Master unit and is displayed on 2 seven segment displays. Only 4 wires are used for communicating between the Master and all the slave units up to 99 rooms or beds. The said communication is capable of working practically over 1500 meters as the same works on RS485 mode. 4 slave units will be supplied with one master module in the kit. |
6880/- |
| 5 |
PC
based wireless paging system with LCD Any Message up to 90 characters typed on a notepad can be sent to a remote wireless handheld unit from a personal computer. The transmitter unit will plug in to the serial port of the PC whereas the receiver is a portable handheld unit with a LCD display. The project is supplied with communication software to enable communication between the two units. The said project demonstrates the use of portable paging system on a UHF frequency range of 433 MHz. One transmitter, one receiver, a serial port cable, and communication software will be provided in the kit. |
5550/- |
|
|
Multipurpose 4 channel RF Remote with ATMEL 89C2051 This is a remote controller which can be widely used in robotic application when in momentary mode. All the 4 channels can be individually programmed as latched outputs for lighting loads or momentary outputs for bell or any other automation requirement. Receiver side is equipped with four relays at the out put which can be wired in any configuration for the required operation. 4 individual addresses can be selected to operate more than one remote kit at a time. |
2850/- |
| 7 |
ATMEL
89C52 based quiz display with priority
function This circuit is a 89C52 based Quiz display capable of handling upto 6 contestants. The first priority persons number will be displayed on a 2.3 inch hieght 7 segment LED display. This project comes with Priority. Means all the contestants are displayed in order of their priority one by one. Two reset bottons take care of the same function.One is Temperory reset and other is the Master reset. |
3880/-
|
|
|
Wireless
fool proof Keyless Ignition system for Cars In contrast to present keys which can be duplicated easily in seconds, presented here is a totally wireless keyless ignition system which is completely fool proof and too the key of this gadget is copy proof. Master units comprises a LCD and a switch to start/ Stop the car and the hand held key is a wireless module transmitting different codes each time the switch is pressed which synchronizes with the pre-fed master codes stored in the Master unit and after confirmation of an valid code, the Master unit activates a relay to switch "ON" the ignition system. Thus the person having the key only will have the access to the car. |
4200/- |
|
|
Digital
"Location display" for Busses and Trains The receiver will have a LCD with backlight and the complete operation of this project is totally automatic. The receiver need to be kept or fitted on the moving Bus/ Train and the transmitters are needed to be kept operating in the particular station where the display is required on the receiver. As the Bus/Train approaches the active transmitter, the display on the receiver will show the name of the approaching station on the LCD. The name of the station may be changed as per individual choices. 4 kits of Transmitters will be provided with one receiver kit |
6800/- |
| 10 |
Secured Access control system with Tamper protection This access control system based on 89C52 is based on digital passwords up to 10 digits for having access to a secured area. The door status is constantly monitored and displayed on a 16x2 LCD module and is highly secured even in an event of power failure. Wrong password protection for 3 attempts and a master code for resetting the system is provided in the system. An intermittent warning buzzer for password tampering and a loud siren is provided to door tampering detection. A on board relay is provided with a 3 Pin connector for any external loads to be connected. |
4300/- |
|
|
RFID
based Keyless lock with Atmel 89C52 Just imagine you at your door of your house and it unlocks as you are nearby or when you wave your wallet waved at its reader. The access to the door is only granted to those persons having a valid RFID card. In case you loose your card, still you can open the door by just entering the 10 digit master code provided with the kit. The door status is constantly monitored and displayed on a 16x2 LCD module and is highly secured even in an event of power failure. Wrong password protection for 3 attempts with intermittent warning buzzer for password tampering and a loud siren is provided to door tampering detection. A on board relay is provided with a 3 Pin connector for any external loads to be connected. In case of invalid card is swiped, the system is deactivated for 60 seconds. The kit will be provided with a RFID reader module, Master kit module, and two valid RFID cards. |
9800/- |
|
|
Remote
controlled security for the Cash Bag Carrying heavy cash is always risky as the person may be attacked by miscreants for the cash and the life of such person is always at threat. Here presented project overcomes the problem by providing wireless remote controlled security for the cash bag. A receiver will be fitted inside the briefcase and a handheld transmitter will be carried by the person. When activated, the Vibration detection mode detects any vibrations and sounds and alarm whenever the bag is moved or snatched. In case the miscreant still decides to run away with the bag with siren sounding, a panic button on the remote can be pressed and the person running with the cash bag will be instantly electrocuted with 440 volts on his body which makes him leave the bag and run for his life. The remote may be effective for a distance up to 100 meters from the bag. The charge delivered by the electrocution is harmless for human life due to minimum current but with high voltage. Please note: Due to advanced design and difficulty level, this project comes completely assembled and tested installed in a briefcase. |
8650/- |
|
|
||
|
This list is updated on 3rd of February 2010 ................Read Disclaimer.......... Download PDF copy of this list |
|
|
United 7 is a sister concern of Electronic Care Centre. All rights Reserverd. Website Designed by United77.com
